writing sip clients. my expertise is with global call and analog cards.
For a few years now I have been using dialogic d/120-jct-ls analog boards and using global call with c#. The software allows people to call in sick and it also dials out to find replacement...
View ArticleWhat's MSP_JITTER_DEPTH_BOARD_LIMIT mean?
Hi,what's the MSP_JITTER_DEPTH_BOARD_LIMIT mean in jitter bufferi want to know whether if it mean a limit for whole board or notis anyone known ?thanks!
View ArticleCan't configure DSI without using s7_mgt
I want configure DSI(SCTP-M2PA-MTP3-SCCP-TCAP-MAP) using only message sending.For start I start s7_mgt with '-d' option and see next log:S7_MGT Tx:...
View ArticleBlind Transfer using Re-Invite
Please tell me how to do a blind transfer using re-invite instead of refer on HMP 3.0 for windows. Thanks.
View ArticleEIR MAP msg flow
Hi, we want to develop EIR. Long back we developed for our organization a long code pull platform which was using spci4 and connected through E1 to MSC.Please suggest me some of my basic querrys.1.My...
View ArticleCPA on HMP taking a lot of time
Hi,I am using HMP Release 3.0 Service Update 347I have also done the Tuning CPA templates forHMP as mentioned by...
View ArticleDiva Server V-Analog-4P/-8P, .Net framework 2.0 and C#.
I am using a Diva Server V-Analog-4P/-8P, .Net framework 2.0, C# and DivaServer.Framework. I have things working fine. I have a few fingernails on the blackboard things.I used the BatchFax example to...
View ArticleDiva, HMP 3 and "ptime" value
We have been entrusitng HMP build 338 to handle all of our low level VoIP settings, and use the Diva ComponentAPI for basic call handling.We have been researching call quality problems with our VoIP...
View Article1 local point codes and 2 DPC in a single SPCI4 Board
Hi I have a requirement where single SPCI4 boards connects to two links( Two different DPC and single local point code). When I have single DPC and LPC it is working fine for both the cases, but it...
View Articlewill Dialogic support BICC over SCTP??
Please confirm whether dialogic will support BICC over SCTP. If yes please share me the configurations.
View ArticleCIRCUIT Blocked
Hi friendsBelow is my config.txt[root@srp2 SIGTRAN_6.4.0]# cat config.txt**** Configure your System IP Addres and Set...
View ArticleDivaSdk 3.5 - 'channel identification' IE in 'setup acknowledge' message...
Hi, I,m trying to solve this issue:I'm using the sdk to monitor isdn calls (on a 32bit windows Server 2003 R2 machine equipped with Eicon Diva PRI, driver 7.5). It worked fine in quite every scenario...
View ArticleGet usage info via MRTG/RRDTOOL from DMG2000
Anyone have the OID to use on the TDM side of a DMG2000 to return current active channels?
View ArticleOutbound call from D4JCTLS
Hello, I currently have a problem when trying to call out from the D4JCTLS card to any extension number (#232 for example) by using the "Out" configuration of the gc_basic_call_model application. From...
View ArticleInteroperability SR140 and Avaya PBX
Dear All; not sure if this is the correct forum for this question?I have an Avaya IP500v2 and IP Office ver 10, Brooktrout SR140 FOIP software, purchased 4 channel SR140 licence, and Microsoft Fax...
View ArticleDMTF detection Issue
Hi,i have the following setup DMV2400A, DMN160TEC and IPT6720 cPCI System.And on some calls mostly with woman voices the called person heres DTMF Tones. I found out that this has something to do with...
View ArticleDownload Diva SDK?
Hi all... We just bought a Dialogic Diva Analog 4 to replace our older Dialogic board. I'm trying to download the sdk, but the download page is blank. Is there another way to download it?thank you!Kevin
View ArticleDivaDeviceStatusType
In a post a few years ago, it was reported that a value of 4 was seen for DivaDeviceStatusType. There was no satisfactory answer in the responses to the post, only that it should not be used when...
View ArticleIs the Dialogic DSI Development Package Release 6.4.2 compatible with windows...
Hi,I have installed the Dialogic DSI Development Package Release 6.4.2 on windows server 2012, and the board was connected on the HP G7 server before the installation. Then I configured the links and...
View Articledx_resetch() returns TDX_RESETERR with system error
Hi everyone,I have a strongly problem, in ocassions when i make dx_stopch the channel is stuck, i'm waiting the event TDX_PLAY 30 seconds and then i run dx_resetch() function, to get idle the Voice...
View ArticleHMP3.0 SU347 SIP SDP keep using 127.0.0.1
Hi,Not sure why the HMP keeps sending 200 OK message with 127.0.0.1 in the c field. Any configuration change this?Thanks,Xu
View ArticleSNMP Monitoring
HiI need to monitor our signalling platform (which contains SS7LD4 boards) using SNMP. However, if I have understood correctly this will provide visibility of (for example) the up/down state of a link...
View ArticleIs SS7HDP 100% COMPATIBLE with the HP DL380 G7?
I’m trying to install SS7HDP dialogic PCI card on HP g7 server DL 380, but it seems that there is a hardware incompatibility between HP G7 servers and Dialogic PCI cards.Our tests were done on...
View ArticleSome questions about CSP
Hello,I have HMP SU347 with SIP, Voice and CSP and I want to listen via sound card to what is happenning on the line using ec_stream function. Everything looks fine except two things:1)When I passed...
View ArticleSCTP ABORT after handshake
Hello all,I have a Dialogic SIGTRAN setup, which stopped working for no apparent reason. SCTP is ABORTed right after COOKIE_ACK as you can see in the attached capture. The same millisecond after ABORT...
View Article